Detailed Guide to Resolve Netgear Firmware Update Failure Issue

The Netgear extender firmware update failure issue has been torturing plenty of Netgear users for weeks now. Are you also unable to update the firmware of your wireless range extender via mywifiext.net? Well, that is unfortunate. But, worry not. We are here to help you regain your faith in luck.

Take the help of the troubleshooting hacks covered in this post and learn how to rectify the Netgear extender firmware update failure issue within minutes.

Rectified: Netgear Extender Firmware Update Failed

  1. Reboot Your Netgear Extender

Have you not tried this hack yet? Nodding your head in yes? Well then, what are you waiting for? Try it now. Walk through the following guidelines in order to reboot your Netgear wireless range extender:

  • Pull out the power cord connected to your extender.
  • Turn off your extender.
  • Wait for a couple of seconds.
  • Turn on your wireless extender.
  • Connect the power cable back to your existing device.

Now, try to update the firmware of your Netgear range extender via mywifiext. If you still didn’t get any luck, why did you stop reading?

  1. Verify the Ethernet Connection

If the Ethernet cable connecting your Netgear extender and router has cuts, then it is quite obvious why you are stuck with the Netgear extender firmware update failure issue.

Therefore, take our advice, and reconnect your devices. And this time, make sure that you are using a damage-free Ethernet cable to do so. Apart from this, ensure that the connection between your devices is not loose.

  1. Pull Your WiFi Devices Closer

The aforementioned point talked about the importance of using a damage-free cable. This one will discuss the significance of the distance between your extender and router.

Too much distance between your Netgear devices can disable them from transmitting signals properly. Thus, to troubleshoot the issue, consider pulling them a bit closer.

  1. Eliminate WiFi Interference

Whether you have performed Netgear EX6100 setup or Netgear EX2700 setup in your home, keeping WiFi interference is vital. The reason being, WiFi interference is one of the biggest reasons behind technical issues.

Therefore, make sure that you haven’t placed your wireless range extender anywhere near electronic devices, metal devices, transmitting appliances, and reflexive surfaces. Some of these things include cordless phones, mirrors, washing machines, cordless phones, fish tanks, refrigerators, treadmills, microwave ovens, televisions, aluminum studs, etc.

  1. Use the Correct Admin Details

Considering you know how to perform Netgear extender firmware update, we don’t have to tell you about the importance of accessing the Genie dashboard for the successful completion of the process.

But, what we can do tell you is, in order to access the Netgear Genie dashboard, using the correct password and username and very important. Therefore, check the admin details that you have entered to log in to your extender. If you find any mistakes in the entree, then consider re-entering the login credentials.

  1. Perform Factory Default Reset

Last, but not least, if you are still going bonkers because of the Netgear extender firmware update failure issue, then it is time that you perform factory default reset.

Caution: Resetting your extender means that it will get restored to its default mode. In simple words, every single change that has been made to your device will get erased. Thus, if you are ready to take this risk, only then reset your wireless extender.

Walk through the below-mentioned instructions and learn how to update your device:

  • Make sure that your device is getting an uninterrupted power supply.
  • Locate the Reset button at the back of your Netgear range extender.
  • Once found, wait no more to press it.
  • Hold on.

And you are done! As soon as you are done performing factory default reset, the next step in line is to perform new extender setup. If you need help in executing the process, feel free to refer to the guidelines given in the Netgear user manual.

Sum Up

Performing Netgear firmware update ensures that your wireless range extender works well. However, if you got stuck during the process, then trust us, there are no better hacks than the ones mentioned above through which you can get rid of this problem.

If hopefully, you do get rid of this issue, take some time out of your schedule and leave a word of appreciation in the comment section for us to see.